The hull, deck or bulkhead can look flawless coming out of the mold, yet after a few seasons reveal an expensive problem: increased weight, local laminate weakening or delamination of facings. Often the source is not the laminate itself but an improperly chosen composite core for boats. In sandwich constructions the core works together with the skins — so it should be judged not only by price per square metre but also by resistance to water, compression, fatigue and by how it is worked.
Why the core determines how the laminate behaves
In a sandwich structure thin, stiff laminate skins carry mainly tensile and compressive stresses, while the core keeps them apart at a fixed distance. That distance significantly increases the stiffness of the part without a proportional increase in weight. The effect matters both in the hull of a powerboat and in lightweight decks, superstructures, bulkheads or interior fittings.
The core must also carry shear stresses and prevent local buckling of the skins. If it is too soft or ill-suited to point loads, the laminate can deflect at equipment fixings, under crew feet or at support points. If it absorbs water, the vessel’s mass increases and the sandwich’s behaviour becomes less predictable.
PET foam used as a structural core meets these demands by combining low weight, low water uptake and dimensional stability. It is not, however, a one-size-fits-all material. The final choice depends on core density, the part’s geometry, the laminating technology, the resin type and the actual service loads.
Composite core for boats made from PET foam
PET foam is a polymer material that can be made using recycled feedstock. In marine use a key feature is its structure that limits water absorption. That matters where a structure will face moisture, spray, condensation or occasional flooding for years.
Unlike wood-based panels, a PET core doesn’t swell or rot when exposed to moisture. It also lacks directionally aligned fibres, so its behaviour is more uniform across the panel. For a manufacturer this means repeatability when routing, cutting and preparing parts for lamination.
Kerdyn™ Green, used by XPET in structural and insulation solutions, can be precisely machined by CNC and delivered shaped to match a specific project. In series production this reduces manual operations and the risk of errors from trimming material directly on the shop floor.
Weight versus performance and operating costs
Every kilogram saved in the superstructure, deck or interior fittings affects the vessel’s weight balance. On powerboats lower weight can reduce fuel consumption and improve performance. On sailing yachts the vertical position of mass is critical — reducing weight high above the waterline can improve stability.
But the lightest core available is not always the best choice. Low density generally means lower compressive strength and less tolerance to concentrated loads. On a large deck with light traffic you can aim for maximum weight savings, but under a seat base, cleat, hinge, auxiliary engine or mast foot you need local reinforcement or a core with higher mechanical properties.
Moisture resistance does not replace good detailing
PET’s low water uptake limits the consequences of damage to the skin, but it does not substitute for a watertight design. Fastener penetrations, cable glands, stanchion bases and the edges of openings require proper sealing. These are the points where water most often reaches the inside of the sandwich.
A practical approach is to remove the core locally at the fixing zone, fill the gap with an appropriately selected structural filler and then make the hole. Alternatives are higher-strength inserts or factory-prepared mounting elements. The choice depends on the load, required precision and production scale.
How to select core parameters for different boat parts
Start selection from the function of the part, not from the available sheet thickness. The hull works under waves, vibrations and variable hydrodynamic loads. The deck must withstand foot traffic and equipment loads. Bulkheads may serve as stiffeners, acoustic or thermal barriers, or contribute to buoyancy. Each application needs separate analysis.
First, the designer defines stiffness requirements and allowable deflection. Then they choose the sandwich layout: the type and thickness of the laminate, the core thickness and its density. In many cases increasing core thickness gives a more beneficial stiffness increase than simply thickening the laminate, but only if the core has sufficient shear and compressive strength.
It is worth analysing at least four areas:
- distributed and point loads, including equipment attachment points;
- production technology, for example hand lay-up, infusion or pressing;
- bend radii and mold geometry, because not every core conforms equally well to curves;
- service conditions, especially the risk of prolonged moisture exposure, temperature and vibration intensity.
For complex shapes the core may require scoring, perforation or pre-forming. Such preparation helps it fit the mold and improves resin flow during infusion. Resin consumption must be controlled: excess resin increases sandwich weight and can weaken the economic benefit of using a lightweight core.
PET, marine plywood or MDF for marine use?
Marine plywood is still used where easy prototyping, high resistance to local bearing loads or traditional work methods matter. It does, however, require consistent protection of edges, openings and surfaces. Even small leaks can start moisture ingress, swelling and long-term structural degradation.
MDF is not suitable for critical, moisture-exposed structures. Its weight and susceptibility to degradation after wetting limit its use aboard, even if it initially seems easy to work with and inexpensive.
A PET core should not be treated as a direct one-to-one replacement for every wooden component. It has different fastening characteristics, different point-load capacity and works best as part of a designed laminate sandwich. Its advantages show where priorities are low weight, water resistance, stability and predictable series production.
Machining and preparation for lamination
Introducing a core material requires an orderly process. Surfaces should be clean and cut blanks precisely matched to the mold. With CNC routing you can prepare holes, channels, pockets for inserts and edges in a single cycle, improving repeatability between units.
Control of bonding and laminating is also crucial. Full support for the skins, the correct amount of resin and clamp conditions appropriate for the chosen process must be ensured. Voids, dry areas and poorly executed joints weaken the sandwich regardless of the core quality.
A well-designed composite core is therefore not merely a lightweight filler. It is an element that lets you deliberately shape a boat’s weight, stiffness and resistance to operating conditions. The best results come from choices based on the loads on the specific part, trial validation of the process and precisely prepared blanks — before the material goes into the mold, not after a problem appears on the water.

