Camper fittings behave differently than a building wall. They are constantly exposed to vibration, intermittent loads, temperature changes and condensation inside. That’s why PET foam for campers should not be seen only as insulation. In a well-designed vehicle it becomes a lightweight structural core, a layer that reduces heat loss, and a material resistant to conditions that quickly degrade wood-based solutions.
In caravanning every kilogram matters. It affects payload, fuel or energy consumption, what equipment you can fit and driving comfort. At the same time, reducing weight must not come at the cost of floor stiffness, wall durability or fastening safety. PET foam lets you combine these requirements, provided density, thickness and lamination method are matched to the function of each component.
What makes PET foam stand out in camper builds?
PET foam is a polymer material used as the core of sandwich elements and as a load-bearing insulation component. Its key feature is a favorable strength-to-weight ratio. In practice that means you can build lightweight panels that, once bonded with appropriate facings, achieve high stiffness.
This is why the layered panel construction is crucial. The foam itself doesn’t automatically replace a structural board in every application. When glued to laminate, aluminium, engineered plywood, composite boards or other facings, however, it forms a panel that works efficiently in bending. Facings take tensile and compressive stresses, while the core keeps them spaced, stabilizes the system and reduces the risk of local deformations.
For a coachbuilder the most important properties are low water absorption, moisture resistance and dimensional stability. In a camper materials can meet water vapour, water brought inside, humidity around windows and doors, and condensation under cladding. Wood-based boards in such conditions may swell, lose geometry and weaken joints. PET foam does not rot and is not prone to the biological degradation typical of organic materials.
PET foam versus plywood and MDF
Plywood has long been popular in vehicle interiors, especially for furniture, floors and mounting elements. Its advantage is familiar machining and the ability to accept screws directly. However, it is heavier than a PET core and, if edges and surfaces are not properly sealed, it remains vulnerable to long-term moisture exposure.
MDF is even less suitable for areas exposed to water and elevated humidity. Its high weight, risk of swelling and limited edge resistance make it hard to justify in mobile constructions except for selected dry interior elements.
PET foam is not a simple drop-in replacement for these boards everywhere in a camper. It should not be used as the direct mounting substrate for heavy equipment without designed reinforcements. Its advantage appears where lightness, insulation and environmental resistance are needed and load-bearing is provided by a composite panel or local inserts. This approach avoids the false economy that comes from using a light material without accounting for real loads.
Where to use PET cores in a recreational vehicle?
The most natural applications are walls, roofs and partitions made as sandwich panels. A lightweight PET core helps reduce the weight of large surfaces while supporting thermal insulation. This matters both in winter when the interior is heated and in summer when the vehicle sits in full sun.
The second area is floors. Here requirements are higher because the structure carries loads from people, furniture, luggage and point pressures. Material selection must consider not only insulation but above all compression resistance, support spacing, facing type and the method of connection to the chassis. In many designs a PET foam with higher mechanical properties, supplemented by local reinforcements in entrance zones, seat mounts, furniture bases and appliance fixings, will be appropriate.
The material also performs well in lightweight interior components: furniture panels, technical partitions, bed bases, housings and doors. In these uses weight reduction can be especially noticeable, since the sum of many small components affects the vehicle’s final weight.
The key rule: design load zones
There is no single universal panel for all locations in a camper. A side wall, roof, floor and furniture partition are loaded differently. The designer should separate areas that work over a surface from points where concentrated forces occur.
Heavy items—awnings, brackets, belts, tanks, seats or heating appliances—require planned attachment points. Solutions may include inserts with adequate strength, profiles, structural inlays or locally reinforced load zones. Don’t assume a regular screw driven directly into the core will provide a durable connection for heavily loaded equipment.
This design approach brings another benefit. Instead of overdesigning an entire panel and increasing vehicle weight, only critical spots are reinforced. The result is a more rational use of material, easier assembly and predictable structural behaviour during service.
Choosing material before production
Before selecting a PET core answer five questions:
- What static, dynamic and point loads will the part carry?
- Will the panel be exposed to water, condensation or contact with a damp substrate?
- Which facings and adhesive will form the sandwich with the core?
- Where are screws, hinges, anchors and equipment attachments planned?
- Is the part primarily meant to insulate, stiffen or carry loads?
The answers help choose density, thickness and material class without costly over-specification. They are also the starting point for process trials, especially when a manufacturer introduces a new adhesive, laminate or press method.
Machining and assembly without accidental quality loss
PET foam can be machined precisely, including in CNC technology. That makes it easier to prepare repeatable panels, holes, milled channels and parts matched to the interior geometry. For series production it means fewer manual adjustments and better assembly repeatability.
Remember that panel quality depends not only on the core. Surface preparation, adhesive system choice, bonding pressure and curing time all matter. Process parameters should be verified for the specific material set. Too little adhesive, uneven pressure or improperly prepared facings can weaken the bond regardless of the foam quality.
Edges are also important. In areas exposed to mechanical damage, water contact or hardware mounting, provide appropriate finishing and sealing. A well-designed detail limits moisture ingress into the panel system and reduces the risk of damage over years of use.
Lower weight is also a production and environmental benefit
Lighter components ease transport, handling on the production line and installation in the vehicle. For a manufacturer this can mean more efficient logistics and less strain on assembly teams. For the user it means more payload reserve or the ability to add equipment without a large increase in total weight.
Material origin also matters. PET fits the circular economy approach, especially when the structural material uses recycled feedstock. In XPET solutions the Kerdyn™ Green foam combines this direction with the properties needed in technical applications: low weight, insulation, limited water uptake and precise machinability.
A good camper doesn’t have to be heavier to be more durable. It does require a conscious division of roles between core, facings and reinforcements. PET foam gives designers a tool to build lighter, moisture-resistant panels—provided it is part of the project from the start, not an accidentally chosen filler.

