When installing a window the gap between the frame and the wall isn’t the only challenge. The longevity of the whole connection also depends on the material under the sill — its compressive strength, resistance to moisture and behavior under long-term loads. Recycled PET foam for construction lets you design this area as a stable structural-insulating element instead of an incidental filler in the installation layers.
For a window and door manufacturer, installer or designer this means reducing thermal bridging without sacrificing load-bearing capacity. A properly selected PET board can carry loads from a window, balcony door or patio door, keep its geometry in high-humidity conditions and be machined precisely for a specific profile. That’s a set of properties not simultaneously offered by typical wood-based boards or standard thermal insulation materials.
what is recycled PET foam?
PET foam is made from polyethylene terephthalate — the same polymer commonly used in packaging. During processing the recycled material is given a foamed structure that combines low weight with the mechanical and dimensional properties required for structural applications. This is not merely reusing packaging material in construction. Final usability depends on controlled density, cell structure, dimensional stability and the mechanical properties of the specific board.
In construction it’s especially important that the PET core can serve two functions at once: reduce heat flow and carry loads. That means you can use a single component tailored to the task instead of combining several materials with different reactions to water, temperature and compression. For base profiles under joinery this simplifies the design of the contact zone between the frame, the insulation layer and the floor.
The recycling aspect matters not only for environmental claims. Using secondary raw material supports a circular economy and reduces demand for primary resources. For companies delivering projects with elevated environmental requirements this is an additional argument, but it should always be accompanied by verification of the material’s performance.
parameters that determine PET’s suitability
Not every plastic board will perform as the support for sliding doors, a base profile under a heavy window or the core of a sandwich panel. The choice should be driven by loads, geometry and working conditions. In practice the key parameters are thermal performance, compressive strength, water absorption and the ability to be milled precisely.
thermal insulation and reducing thermal bridges
A base profile made from a material with favourable thermal properties limits cooling of the lower part of the reveal. This is particularly important for large glazed areas, low thresholds and installations in the insulation layer. Using a PET element helps maintain continuity of insulation between the frame profile, the wall and the floor insulation.
However, the effect doesn’t depend solely on the material. The height and width of the base profile, layer arrangement, connection to the waterproofing and the tightness of joints all matter. Even a material with a good thermal conductivity won’t fix the problem if the detail’s geometry creates an insulation discontinuity.
load-bearing capacity and stability under load
In the support zone of joinery insulation must work together with mechanical strength. PET foam with an appropriately selected density shows the compressive resistance needed to carry loads from frames, glazing, sashes and daily operation. For patio doors and sliding systems you should analyse not only the total load but also its distribution at support points.
How the material behaves over time is also important. A base profile must not deform excessively under long-term pressure, because that can affect sash alignment, hardware operation and joint tightness. Therefore selecting the board should consider service loads, not only catalogue values for short-term compression.
minimal water absorption and resistance to site conditions
The lower part of a window opening is exposed to rainwater, construction moisture, capillary rise from improperly protected layers and periodic wetting during installation. Wood-based materials can swell, lose shape and require extra edge protection in such conditions.
PET is characterised by very low water absorption, so it doesn’t inherit common problems of unprotected MDF or plywood. That doesn’t mean you can skip correct waterproofing of the threshold. The material reduces the risk of element degradation but doesn’t replace properly designed water drainage and tight layer connections.
applications in construction
The most recognised use is base profiles for windows and doors. A routed PET element can be prepared for a specific profile geometry, accounting for chambers, thresholds, extensions and the planned installation method. That accuracy cuts the need for on-site trimming, shortens installation time and reduces the risk of leaks.
In warm installation of joinery the material can act as a continuous insulating support. This matters especially in energy-efficient homes where the detail at the threshold often determines the real quality of the whole enclosure. The base profile should match the mounting system, the weight of the joinery and the expected contact with the floor, terrace or external insulation layer.
PET foam is also used beyond joinery. It can serve as the core of lightweight sandwich panels, a component for transport enclosures, a structural element in caravanning or part of solutions for the marine and wind energy industries. In these sectors the stiffness-to-weight ratio, moisture resistance and predictable CNC machining are particularly valued.
PET vs plywood, MDF and classic insulations
Comparing materials requires reference to a specific task. Plywood and MDF are widely available and familiar to tradespeople, but in moisture-exposed zones they need protection and don’t offer comparable insulation. Their weight can also complicate logistics and installation of larger elements.
Classic insulations like XPS provide good thermal properties but aren’t always the right choice where precise routing, controlled load-bearing capacity and durable support for heavy joinery are required. PET sits between these material groups: it combines insulating and structural functions while allowing machining consistent with system installation demands.
That doesn’t mean PET is universal for every detail. Under extreme point loads, specific fire-resistance requirements or unusual chemical conditions a separate project analysis is necessary. The right solution results from calculations and working conditions, not the material name alone.
how to choose a PET component for a project?
Selection should start before ordering the joinery, once profiles, sash weights and the final floor or terrace layers are known. That way you can prepare an element with the correct height and geometry, instead of compensating on site with additional shims.
When providing data to the manufacturer specify at least:
- type and cross-section of the window or door profile,
- dimensions and mass of the structure,
- support method and arrangement of load points,
- layout of insulation, waterproofing and finished floor levels,
- required routing scope, lengths and installation tolerances.
For serial production of joinery repeatability is important. Ready-routed base profiles remove some manual operations and help maintain consistent quality across projects. XPET supplies solutions made from Kerdyn™ Green PET foam tailored to specific profiles, allowing structural requirements to be delivered as a ready-to-install component.
The material under a window or door works for years while remaining hidden after installation. That’s precisely why it should be treated as a structural part that determines airtightness, energy performance and durability of the whole detail — not as a line where apparent savings are best sought.

